How To Change Oil In Honda Lawn Mower

Use The Dipstick To Check The Quality

The dipstick can also offer more information. It can be a great way to quickly get a sense of the quality of the oil remaining in your mower.

Fresh and good quality oil should be amber in color and free of debris.

If your dipstick pulls up black oil or has bits of debris showing, then its definitely time to change your oil.

If the oil is still a good amber color and is free of debris but perhaps a bit low, then its okay just to top it up a bit by adding oil directly into the oil well of your lawn mower.

Youll be able to tell if the oil level is too low or too high based on the indicators on the dipstick itself that will usually have markings that read full or low.

My one tip about topping off your mowers oil level is to add a little, then check again.

Many people add too much oil, and its easier to add a little at a time, than to waste oil by having to dump some out after overfilling your reservoir.

What Type Of Oil Should I Use In My Honda Lawn Mower

theHondausingoilusemoweruse

Honda engines are developed, tested and certified with petroleum based motor oils as a lubricant. Synthetic oils may be used however, any motor oil used in our engines must meet all oil requirements as stated in the owner’s manual. In addition, recommended oil change intervals must be followed.

Also Know, can you use regular motor oil in a lawn mower? SAE 30 motor oil is commonly recommended for use in a lawn mower engine, but the safest best is to use the type of oil your lawn mower manufacturer recommends. Often 10W-30 or 10W-40, the same motor oil types that are used in vehicles, can also be used in a lawn mower.

Moreover, what is the best oil to use in a lawn mower?

For most mowers and weather conditions, your best bet is going to be SAE 30/SAE 10W-30 oil. These oils are ideal for operation in warmer environments.

What type of oil does a Honda gcv160 take?

Features

Get The Lawn Mower Ready For An Oil Change

• Turn the engine on and heat it well. This will increase the flow of oil and make it easier to remove the oil.
• Use an air compressor or a clean towel to wipe well around the oil insert area.
• Take an oil pan to collect the oils that are already in the mower oil tank.
• Place the oil pan just below the oil drain pipe.

You May Like: Clean A Small Engine Carburetor

How To Change Oil In A Honda Lawnmower

You might not be accustomed to your lawnmowers oil changes if you havent done this before. Whether you own one for some time, or youve just purchased a brand-new unit from the renowned automotive giant Honda, after a decent amount of use, youre wondering if your device needs an oil change or not. Furthermore, you are also looking at what type of oil suits the needs of your device. Well then, we have good news for you since this article covers all the information related to the subject. Besides, we also throw some light on some of the frequently asked questions about Honda lawnmowers and lawnmowers in general.

Oil changes are significant if you want your device to run long and avoid maintenance expenses time and again. Generally, it is recommended to change the oil after a maximum of 50 hours of use. If youve just started your device after a long season break, then it might be a high time for an oil change. Generally, when the oil appears black on the dipstick, it should be replenished soon.

How to Change Oil in a Honda Lawnmower:

Contents

How To Check Oil Level

Make it a habit to check the oil level and appearance each time you’re about to start a small engine. Checking the oil while the engine is cold and most of the oil is in the crankcase yields the most accurate reading.

For oil checking procedures on lawnmower applications, please watch our “Checking Engine Oil – Lawnmower Engine” video:

• Step 1: Locate the oil fill cap on the crankcase to start. Fill cap locations vary, depending on the make and model of your engine.

• On newer models, look for an oil can symbol or the word “oil” or “fill” stamped on the plug.
• On small tractors, you may have to lift the hood to locate this cap.
• Some engines contain either an extended oil fill tube or a standard fill hole with a dipstick for inspection.
• Others require you to remove the fill cap to check that the oil is at the fill line or the top of the fill hole.

• Step 2: Clean the Crankcase: To prevent dirt and debris from falling into the crankcase, use a clean cloth to wipe the area clean before removing the cap.

• Step 3: Inspect the Oil. If there is no dipstick, dab the oil with a clean tip of the cloth to inspect the oil. If the engine includes a dipstick cap, remove the dipstick and wipe it with a clean cloth.
• To ensure an accurate reading, reinsert the dipstick completely. If the dipstick cap is a screw-in type, ensure an accurate reading by screwing in all the way before removing it to check the level.
• Then, remove it again and check the oil level.

Don’t Miss: How To Fix Dead Patches In Lawn

Is Sae 30 The Same As 10w

When the engine is cold, 10W-30 indicates that the oil has a viscosity of 10W and 30 when it is hot. If you considered factors such as temperature while making this choice, it would help. SAE-30 is a single-grade oil suitable for conditions where its elevated temperature and variability are not significant. Whereas if your weather continues to vary, then you can use 10W-30. It also improves cold-starting at lower temperatures as compared to SAE-30. Therefore, if you live in moderate or milder climates, then the use of SAE 30 or 10W-30 does not make a significant difference in engine performance.

Can I Use Full Synthetic Oil In My Honda Lawn Mower

3.9/5Can I use synthetic oil in my Honda engineSynthetic oilsoilall oil

Yes! We have modified our engine oil recommendations to state that you may now use a synthetic 5W30 or 10W30 oil in all temperature ranges. Keep in mind that the use of synthetic oil does not prevent you from performing your regularly scheduled lawn mower maintenance .

Additionally, is synthetic oil OK for small engines? While conventional oils are effective for your small engine, the improved synthetic oils offer more benefits, making it a more popular and better choice for your engine. These oils offer better viscosity, wear and deposit control and low-temperature fluidity.

People also ask, what is the best oil for Honda lawn mower?

The owner’s manual says to use 10W30 oil although 30 weight oil can also be used.

Is synthetic oil better for lawn mower?

Benefits of Synthetic OilBut for lack of a better term, synthetic oil is slipperier than conventional oil. This means that it will lubricate better, keeping your engine moving as needed, and will help your engine be efficient. Synthetic oil also protects and lubricates in the widest temperature range.

Don’t Miss: How To Kill Wild Violet Weeds In Lawn

What Happens If You Do Not Change The Oil In A Lawnmower

The engines wear rate increases if an oil change hasnt been performed timely. Also, most lawnmowers do not have an oil filter. Resultantly, it takes very little time for the oil quality to deteriorate. Moreover, the oil is responsible for the cooling of the engine apart from the air-cooling. The engines service life does not meet its predicted lifespan by its manufacturer. Therefore, one should always pay heed to ensure timely oil changes in the machine.

How Do You Change The Oil In A Honda Push Mower

How to Change the Oil of a Honda HRX/HRR Lawn Mower

Just so, what kind of oil does a Honda push mower take?

SAE 10W-30 Motor Oil

how do you change the oil in a push mower? Instructions

Also to know, how much oil does a Honda push mower take?

Engine Type Determines CapacityThis 6.5-horsepower engine holds 0.58 quarts of oil and does not have an oil filter. For normal operating conditions, the manufacturer recommends using an SAE 10W-30 weight oil with an American Petroleum Institute rating of SJ or later.

Can you use synthetic oil in a Honda lawn mower?

Honda engines are developed, tested and certified with petroleum based motor oils as a lubricant. Synthetic oils may be used however, any motor oil used in our engines must meet all oil requirements as stated in the owner’s manual. In addition, recommended oil change intervals must be followed.

Oilengine

Ouissam Marfelev

Also Check: How To Kill Creeping Charlie In Lawn

How To Change The Oil In A Honda Self

21 September, 2017

Maintaining a Honda self-propelled mower is much like maintaining any other mower. The Honda self-propelled mower has a transmission that allows you to walk behind the mower rather than push it. To change the oil in a Honda self-propelled mower, no adjustments are necessary to the transmission but you need to follow a few safety guidelines before working on your mower. Check your engine oil before each use and change it after every 50 hours of use.

Turn off the fuel valve located on the left side of the Honda self-propelled mower motor, below the fuel tank and next to the carburetor. Disconnect the spark plug wire by pulling it from the spark plug located on the front of the mower motor. Follow these two safety steps to avoid any injury to yourself or damage to your mower.

• Maintaining a Honda self-propelled mower is much like maintaining any other mower.
• To change the oil in a Honda self-propelled mower, no adjustments are necessary to the transmission but you need to follow a few safety guidelines before working on your mower.

Remove the filler cap/dipstick from the oil filler neck located on the right side of the motor. Make sure you wipe the filler area clean so no debris washes back into the oil tank.

Drain the oil from the Honda self-propelled mower while the engine is still warm. The oil drains faster and more completely from a warm engine than from a cool engine.

Related Articles

How To Change Lawn Mower Oil

More About toolrepair »This article and its video explain how to change lawn mower oil on most mowers, and how to change oil filters on mowers that have them.

The small engines that run lawn mowers need their oil changed just like car engines. Most mower engines need their oil changed every 20-50 hours of operation.

A mower’s owner’s manual will indicate how often to perform oil changes on the mower. At the very least, an oil change should be done annually with other seasonal tune-up maintenance.

This article explains the steps for changing oil in most mowers. Changing mower oil is very simple and can take as little as five minutes.

Also Check: Does Aarons Rent Lawn Mowers

Locate The Drain Plug Of Your Mower

The drain plug on this mower has a 3/8 square hole in it, which is the same size as the nub on a socket wrench without a socket on it. An alternate location for the drain plug is on the side of the engine as seen in this version of the same Briggs and Stratton engine:

S To Fit Mower Crankshaft Seal

Most seals are fitted using a wipe of engine oil to help fitting and sealing, however, some seals need to be fitted dry, so consult with your part supplier first. The mating surfaces need to be clean and free from dirt but do not use anything metal to clean the surfaces, likewise do not use sandpaper. If you require an abrasive, use the scouring face of a household sponge.

I use a deep socket to drive the seal in this guide, you may not have one. Instead use a suitable size piece of timber and hammer, plastic plumbing pipe cut to size makes a useful driver, or use a rubber hammer. The seal must be driven home square, gently tapping uniformly all the way around the seal will seat it correctly.

Clean & lube With the sealing surfaces clean, lube your seal if applicable.

Gently Start the seal by tapping it gently, one side and then the other.

Drive Im using a deep socket to drive the seal. This is the preferred way as it drives the seal squarely.

Home Use your reference marks or picture you took earlier to note where the seal seats are. Over egging the seal will damage it.

Thats it, you did it, Nice work! Now refit the engine and not forgetting to refill the oil.

Don’t Miss: First Zero Turn Mower

Pennzoil Sae Lawn Mower Oil

The SAE 30 graded oil controls the formation of deposits and even high-temperature oxidation. The product cleans out engines by lifting sludge deposits from the surface and dissolves the same. It is ideal for cleaning up to 40 percent of engine sludge in the first and second oil change also.

After a lot of contemplation, my choice is the Briggs & Stratton SAE 5W -30 Synthetic Small engine motor oil. 100074. The product has low volatility and gives your engine better viscosity temperature response and better thermal stability. You can find the products link in table.

Refill The Tank With Oil

• According to the user manual of Toro lawn mower and Honda lawn mower,

• The refilled amount of oil is 0.35~0.40 L.
• The recommended oil for regular use: SAE 10W-30.

• Now, refill the oil tank. Stop after pouring the oil for a while and wait for a couple of minutes. Check the oil level with the dipstick. Continuing to check in after a while will help prevent oil from falling over.
• Place the lid on the tank.

Done. Now, you can use the lawn mower with ease.

Recommended Reading: How Much Lime To Put On My Lawn

Match Weight To Conditions

Under normal operating conditions, where the air temperature is between 0 and 100 degrees Fahrenheit, Honda recommends using SAE 10W-30 oil. If you plan to use your mower for long periods of time in temperatures above 90 degrees, however, use SAE 30 to reduce internal wear. For temperatures 20 degrees Fahrenheit or colder, use thinner SAE 5W-30 weight oil. Honda engines require four-stroke automotive detergent oil. Honda warns that using nondetergent oil in its 6.5-horsepower engines leads to faster wear of internal parts, and use of two-cycle oil results in damage to the engine.

Better Late Than Never

If youve had a mower for years and havent ever checked or changed the oil, dont despair!

Now is a perfect time to start, and many well-made lawn mowers are resilient to a certain degree of neglect.

Just because youve managed to use your mower for two seasons without any problem, doesnt mean you wont run into problems that could send your mower to the scrap yard.

So head to the hardware store, buy the right oil for your mower, and get her purring like a kitten the next time you mow.

Recommended Reading: What Herbicide Kills Wild Violet

How Much Oil For A Honda 65 Mower

Related Articles

• Type of Oil to Use in Husqvarna Riding Mowers

When youre maintaining the 6.5-horsepower engine on your Honda push mower, its important to know how much oil to add. Hondas four-stroke, air-cooled engine has an oil reservoir, eliminating the need to mix the oil with the gasoline to lubricate the engine. Though this makes caring for the mower easier, it is important to maintain the correct level of oil to avoid damaging the engine.

S To Remove Lawnmower Crank Seal:

Gain Access Drain the engine oil to begin and pull your walk behind the mower spark plug wire . Always turn to walk behind mower over with carburetor side facing up prevents oil spill and starting issues.

Fitting a walk-behind mower seal remove blade and boss. Need help, check out the Blade fitting video.

Tractor Engine out.

Pic Note how the seal seats, this will be valuable info to you later when driving home the new seal.

Drill An oil seal puller is the right job, but you might not have, instead carefully drill into the center of the seal, it helps start the screw.

Fit screw A rough thread screw is perfect for removing the seal, use two, one on each side if you prefer.

Vice Grips What would the world look like without the trusty vice-grips.

Ease it out Having a screw on either side and two vice-grips will give you greater control when removing.

Gently does it Remove it with care, rough play will mark engine seal surfaces, and that will cause an oil leak that cant be fixed easily.

Don’t Miss: How To Estimate Lawn Mowing Jobs